![]() The process of adopting a device requires that the device is able to talk to the controller. For smaller networks the USG is intended to act as the DHCP server, so devices behind the USG will end up with an address in 192.168.1.0/24. The internal network of the USG by default uses network 192.168.1.0/24 with the USG using IP 192.168.1.1. Huh!Īfter a bit of futzing around and digging through the Unifi help forum it dawned on me what the problem is: The USG shows up in the Devices list ready for adoption, I click and almost immediately get "Adoption Failed". I played around with the settings until I was confident in what and how I want to set this up.Īfter factory reset I connected the LAN port of the USG to my internal network, and in a browser went to the existing controller on that network. The process of adopting the USG to that controller worked just fine. Of course, in order to now configure the USG, I need a controller on that laptop. Adding a USG to the mix turned out to be surprisingly non-intuitive.Īt first I took the common route of connecting the WAN interface of the USG to my internal network, and a laptop to the internal network behind the USG. I have a couple Unifi accesspoints, and a bunch of Linux infrastructure including an existing controller. Unless you are building a completely new network, you might already have Unifi devices installed in your network. A core feature of these units is that a software controller holds all the relevant information about a site, and centrally configures the respective devices at that site. The USG will only update Namecheap when it detects an IP change.Ubiquiti Networks makes the Unifi Security Gateway (USG) as part of their Unifi series of enterprise networking products. If you aren’t sure of your credentials you can find them in UniFi → Settings → Site → Device Authentication. Part of this process involves logging into the USG via SSH. However, there are ways to speed this process up. It may take a while to propagate changes. That’s it! It might not work immediately – that’s the nature of DNS. If you’re using another DDNS, like NoIP, that gives you an explicit username, use that instead of the TLD for “username” (thanks for the tip, R!): Here’s what configuring a house’s USG to update would look like: Server: I found this from other Namecheap tutorials: Password: This is the password from the Namecheap settings (ex. Other DDNS services may give you a specific username (ex. Username: For Namecheap, this is the top level domain with no subdomain (ex. ![]() If you’re using the top-level domain (ex. Hostname: If you’re using a subdomain, this is the first segment (ex. If you’re using the new Settings meeting, go to Settings → Gateway → Dynamic DNS. In UniFi, go to Settings → Services → Dynamic DNS. Set up a Dynamic DDNS record for domain if you haven’t already using Namecheap’s tutorial That’s the machine where the DDNS client software operates. You have to have a Ubiquiti Unifi Security Gateway in your setup for this to work. All that’s needed is the right combination of settings! How-To Prerequisite Namecheap is a domain registrar that provides DDNS services to its customers, and UniFi supports Namecheap out-of-the-box. ![]() ) with this address so you only have to memorize the domain instead of a new number sequence every time it changes. Dynamic DNS (DDNS) services allow you to sync a domain (ex. One peculiarity of that setup is that residential internet connections typically have a constantly changing (dynamic) IP address instead of static. It’s popular with ” prosumers” who often use it to run services like websites, home automation, etc. Ubiquiti UniFi is a line of networking equipment. I’ve done this a few times now and each time I piece the answer together from forum posts and trial & error… that’s my indicator the internet is missing a good how-to tutorial □ Quick Intro Dalton Flanagan Configuring Ubiquiti UniFi USG to use Namecheap DDNS
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |